아무런 노력을 하지 않고 승진이나 연봉인상을 꿈꾸고 있는 분이라면 이 글을 검색해낼수 없었을것입니다. 승진이나 연봉인상을 꿈꾸면 승진과 연봉인상을 시켜주는 회사에 능력을 과시해야 합니다. IT인증시험은 국제적으로 승인해주는 자격증을 취득하는 시험입니다. ITExamDump의Juniper인증 JN0-660덤프의 도움으로 Juniper인증 JN0-660시험을 패스하여 자격증을 취득하면 승진이나 연봉인상의 꿈이 이루어집니다. 결코 꿈은 이루어질것입니다.
인재도 많고 경쟁도 많은 이 사회에, IT업계인재들은 인기가 아주 많습니다.하지만 팽팽한 경쟁률도 무시할 수 없습니다.많은 IT인재들도 어려운 인증시험을 패스하여 자기만의 자리를 지키고 있습니다.우리ITExamDump에서는 마침 전문적으로 이러한 IT인사들에게 편리하게 시험을 패스할수 있도록 유용한 자료들을 제공하고 있습니다.
ITExamDump에서는 가장 최신이자 최고인Juniper인증 JN0-660시험덤프를 제공해드려 여러분이 IT업계에서 더 순조롭게 나아가도록 최선을 다해드립니다. Juniper인증 JN0-660덤프는 최근 실제시험문제를 연구하여 제작한 제일 철저한 시험전 공부자료입니다. Juniper인증 JN0-660시험준비자료는 ITExamDump에서 마련하시면 기적같은 효과를 안겨드립니다.
ITExamDump Juniper인증JN0-660시험덤프 구매전 구매사이트에서 무료샘플을 다운받아 PDF버전 덤프내용을 우선 체험해보실수 있습니다. 무료샘플을 보시면ITExamDump Juniper인증JN0-660시험대비자료에 믿음이 갈것입니다.고객님의 이익을 보장해드리기 위하여ITExamDump는 시험불합격시 덤프비용전액환불을 무조건 약속합니다. ITExamDump의 도움으로 더욱 많은 분들이 멋진 IT전문가로 거듭나기를 바라는바입니다.
많은 사이트에서도 무료Juniper JN0-660덤프데모를 제공합니다.우리도 마찬가지입니다.여러분은 그러한Juniper JN0-660데모들을 보시고 다시 우리의 덤프와 비교하시면 ,우리의 덤프는 다른 사이트덤프와 차원이 다른 덤프임을 아시될것입니다, 우리ITExamDump에서 제공되는 덤프는 100%보장 도를 자랑하며,여러분은 시험패스로 인해 성공과 더 가까워 졌답니다
시험 번호/코드: JN0-660
시험 이름: Juniper (Service Provider Routing and Switching, Professional (JNCIP-SP))
당신이 구입하기 전에 시도
일년동안 무료 업데이트
100% 환불보장약속
100% 합격율 보장
Q&A: 248 문항
업데이트: 2014-03-02
ITExamDump는 여러분의 요구를 만족시켜드리는 사이트입니다. 많은 분들이 우리사이트의 it인증덤프를 사용함으로 관련it시험을 안전하게 패스를 하였습니다. 이니 우리 ITExamDump사이트의 단골이 되었죠. ITExamDump에서는 최신의Juniper JN0-660자료를 제공하며 여러분의Juniper JN0-660인증시험에 많은 도움이 될 것입니다.
JN0-660 덤프무료샘플다운로드하기: http://www.itexamdump.com/JN0-660.html
NO.1 Click the Exhibit button.
As shown in the exhibit, you have an adaptive LSP that requires 85 Mbps. The LSP is configured with a
primary path and a secondary path in standby mode. All connections in the MPLS network are Fast
Ethernet. Which statement is correct?
A. The primary and secondary paths are in an up state and operational.
B. The primary and secondary paths are in a down state and not operational.
C. The secondary path is in a down state and not operational.
D. The primary path is in a down state and not operational.
Answer: A
Juniper최신덤프 JN0-660기출문제 JN0-660 JN0-660 dump JN0-660 dumps
NO.2 You are provisioning a new customer for access to your Layer 3 VPN. The customer is using
172.16.35.0/24 as their internal IP address space, which is also being used by an existing Layer 3 VPN
customer. The two customers share many PE routers in common across your network. Which mechanism
allows these duplicate addresses to exist in your network?
A. route origin
B. route target
C. route refresh
D. route distinguisher
Answer: D
Juniper JN0-660 dumps JN0-660 pdf
NO.3 You are the administrator for a network that uses IBGP. As the network grows, you must examine
options to support increased scale.
Which two scaling options should you consider? (Choose two.)
A. route reflection
B. areas
C. zones
D. confederations
Answer: B, C
Juniper JN0-660 JN0-660 JN0-660
NO.4 Which operational mode command displays the number of configured forwarding classes?
A. show interfaces queue ge-1/0/0
B. show interfaces terse
C. show class-of-service interface
D. show forwarding classes
Answer: A
Juniper JN0-660 dumps JN0-660 JN0-660자료 JN0-660
NO.5 Click the Exhibit button.
All networks shown in the exhibit contain more than one BGP speaking router. You operate ISP A.
You must ensure that customer Y sends their traffic to you over the directly connected link but customer Y
is not used for transit into your network. What do you do to accomplish this? A. Advertise routes to
customer Y with the well-known no-transit community.
B. Advertise routes to customer X with the well-known no-advertise community.
C. Advertise routes to customer Y with the well-known no-export community.
D. Advertise routes to customer X with the well-known as-transit community.
Answer: C
Juniper자격증 JN0-660 JN0-660
NO.6 Click the Exhibit button.
All routers in the exhibit are running IS-IS level 2 routing. The wide-metrics-only parameter is configured
on all routers. Which metric does R1 see for the path to R4?
A. 136
B. 138
C. 310
D. 320
Answer: D
Juniper JN0-660 JN0-660 dumps JN0-660 dump
NO.7 You manage an MPLS network where the PE devices consist of multiple vendors.
You are asked to conceal the MPLS topology for all LSPs.
Which global configuration parameter will accomplish this?
A. Configure no-decrement-ttl on the ingress router only.
B. Configure no-propagate-ttl on the ingress router only.
C. Configure no-decrement-ttl on all routers within the MPLS network.
D. Configure no-propagate-ttl on all routers within the MPLS network.
Answer: D
Juniper JN0-660 JN0-660 JN0-660자격증 JN0-660
NO.8 Click the Exhibit button.
Referring to the exhibit, which type of traffic protection mechanism is used for the LSP?
A. fast-reroute
B. link-protection
C. node-link-protection
D. secondary
Answer: B
Juniper dumps JN0-660 pdf JN0-660 pdf JN0-660인증
NO.9 Click the Exhibit button.
Referring to the exhibit, which MPLS feature was used to make the LSP the preferred path for internal
routes.?
A. traffic engineering bgp-igp
B. traffic engineering shortcuts
C. traffic engineering mpls-forwarding
D. install active
Answer: C
Juniper기출문제 JN0-660 JN0-660 JN0-660기출문제 JN0-660
NO.10 Click the Exhibit button.
In the exhibit, ISP A is charged a higher rate for traffic sent to R2. You are asked to lower costs for ISP A
by configuring R1 to send traffic to R3 whenever possible.
What are two ways to do this? (Choose two.)
A. set protocols bgp group isp-b neighbor 192.0.2.6 local-preference 120
B. set protocols bgp group isp-b neighbor 192.0.2.6 local-preference 80
C. set protocols bgp group isp-b neighbor 192.0.2.10 local-preference 120
D. set protocols bgp group isp-b neighbor 192.0.2.10 local-preference 80
Answer: B, C
Juniper최신덤프 JN0-660 dumps JN0-660인증
NO.11 Click the Exhibit button.
You are asked to configure an OSPF network based on the topology shown in the exhibit. You must keep
the link-state database in Area 1 as small as possible. What will accomplish this?
A. Area 0 should be configured as a stub area so that it will not announce routes into Area 1.
B. Area 1 should be configured as an NSSA to limit the size of the link-state database.
C. Area 1 should be configured as a stub area with no-summaries to limit the size of the link-state
database.
D. Area 0 should be configured with a virtual link to R4 to limit the size of the Area 1 link-state database.
Answer: C
Juniper dump JN0-660인증 JN0-660시험문제 JN0-660시험문제 JN0-660 JN0-660덤프
NO.12 Click the Exhibit button.
On your MX Series router, traffic using the critical scheduler is out of profile. All other data is currently in
profile. Referring to the exhibit, which statement is correct?
A. The critical queue is serviced before the less-critical queue.
B. The critical queue is serviced after the left-over queue.
C. The critical queue is serviced before the data queue.
D. The critical queue is serviced before the voice queue.
Answer: B
Juniper pdf JN0-660 JN0-660 dumps JN0-660
NO.13 Which CoS feature supports per-VLAN queuing and scheduling?
A. multilevel scheduling
B. hierarchical scheduling
C. tagged queuing
D. per-instance queuing
Answer: C
Juniper기출문제 JN0-660 JN0-660자격증 JN0-660
NO.14 Click the Exhibit button.
Based on the configuration in the exhibit, which statement is correct?
A. The 172.20.20.0/24 route is installed in the inet.0 table with the next hop of the LSP.
B. The 172.20.20.0/24 route is installed in the mpls.0 table with the next hop of the LSP.
C. The 172.20.20.0/24 route is installed in the inet.3 table with the next hop of the LSP.
D. The 172.20.20.0/24 route is installed in the inet6.3 table with the next hop of the LSP.
Answer: C
Juniper기출문제 JN0-660 pdf JN0-660최신덤프
NO.15 Your are the administrator for a network that uses IS-IS as its IGP. As the network grows, you find that
the protocol's default capabilities for setting metrics is limiting your options. Which feature can you
implement to provide a larger range of metric configuration capabilities?
A. extended metrics
B. wide metrics
C. expanded metrics
D. full metrics
Answer: D
Juniper pdf JN0-660시험문제 JN0-660
NO.16 Click the Exhibit button.
In the exhibit, Area 1 is a not-so-stubby area.
Three networks are redistributed into Area 1 on R2.
You must summarize the redistributed network addresses in Area 1 so that only one network prefix is
re-advertised into Area 0. You must also summarize the loopback addresses of R1 and R2 into a single
address in Area 0.Which configuration sample on R3 and R5 will complete this task?
A. Option A
B. Option B
C. Option C
D. Option D
Answer: C
Juniper JN0-660시험문제 JN0-660인증
NO.17 Which two statements are true about OSPFv3? (Choose two.)
A. OSPFv3 uses a 32-bit router ID to uniquely identify a node in the network.
B. OSPFv3 uses a 128-bit router ID to uniquely identify a node in the network.
C. OSPFv3 routes are always preferred over OSPFv2 routes for all traffic.
D. OSPFv3 and OSPFv2 can be configured at the same time.
Answer: A, D
Juniper JN0-660자료 JN0-660 JN0-660 JN0-660자료 JN0-660
NO.18 Click the Exhibit button.
Given the drop profile in the exhibit, what is the drop probability when the buffer reaches 90% full?
A. 60%
B. 70%
C. 85%
D. 90%
Answer: B
Juniper JN0-660기출문제 JN0-660최신덤프 JN0-660최신덤프 JN0-660
NO.19 Your multicast receivers are indirectly connected to an MX Series router. The receivers need to join
multicast group 224.2.2.2. What must be configured in IGMP to receive report messages from receivers
that are multiple hops away?
A. By default, IGMP accepts report messages from indirectly connected receivers.
B. Promiscuous mode must be enabled in IGMP.
C. Promiscuous mode must be disabled in IGMP.
D. DVMRP protocol must be configured.
Answer: B
Juniper JN0-660 JN0-660
NO.20 In which two ways does VPLS populate the MAC table? (Choose two.)
A. dynamically using BGP
B. dynamically using the source MAC address on received frames
C. dynamically using LDP
D. statically using CLI
Answer: B, D
Juniper시험문제 JN0-660덤프 JN0-660
ITexamdump의 C_FSUTIL_60덤프의 VCE테스트프로그램과 VCAC510덤프는 한방에 시험을 패스하도록 도와드립니다. ITexamdump 에서는 최신버전의 1Z0-536시험에 대비한 고품질 덤프와 C_TSCM52_64시험 최신버전덤프를 제공해드립니다. 최고품질 FCNSP.v5시험자료는 100% 간단하게 시험패스하도록 최선을 다하고 있습니다. IT인증시험패스는 이토록 간단합니다.
댓글 없음:
댓글 쓰기